Glue Joint Rip Blades And ATB Rip Blades For Table Saws And Rip Saws, Including Mereen-Johnson, Diehl, Raimann And SCM

Choosing the Right Saw Blade

Tooth Geometry Explained

Combination Table Saw Blades

Miter Saw Blades

Radial Arm and Chop Saw Blades

Rip Saw Blades

Glue Joint and ATB Rip Saw Blades

Trim Blades for Table Saws

Aluminum Cutting Blades

General Purpose Table Saw Blades - ATB

General Purpose Table Saw Blades - TCG

Dado Sets

Plastic Cutting Blades

Melamine Saw Blades

Solid Surface Blades

Steel Cutting Blades

Our Policies

Contact Us

Glue Joint Rip Blades - Triple Chip Grind

Glue Joint Rip Blades are designed for ripping solid wood when you require an extra-smooth cut such as cutting solid pieces that will be glued together. And with the tight manufacturing tolerances of Popular Tool blades and a runout of .002" or less, these blades will give you the smoothest rip cuts you can imagine.

All of these rip blades have a 20º hook angle and should be used for rip cuts only. Glue Joint Rip Saws can be bored out to fit most gang rip saws. Email service@justsawblades.com for information on this service.

Diameter	Teeth	Bore and Pinhole	Kerf	Plate	Design	Item #	Price
10"	30T	5/8"	.145"	.102"	TCG	GJ1030	97.00
10"	30T	5/8"	.125"	.087"	TCG	GJ1030125	67.00
300mm	36T	80mm, 2 key	4.2mm	3.2mm	TCG	GJRM30036***	106.00
300mm	48T	80mm, 2 key	2.8mm	2.0mm	TCG	GJRM3004828***	118.00
12"	36T	1"	.160"	.118"	TCG	GJ1236	99.00
12"	36T	3 1/8"	.160"	.118"	TCG	GJM1236157*	109.00
12"	36T	70mm, 2 key	.160"	.118"	TCG	GJ1236K	102.00
12"	48T	1"	.157"	.118"	ATB	GJ1248ATB	132.00
12"	50T	1"	.134"	.094"	ATAF+R	GJL1250****	130.00
14"	36T	1"	.177"	.138"	TCG	GJ1436177	128.00
14"	36T	2", 2 PH	.177"	.138"	ATB	GJ1436DA**	128.00
14"	36T	2", 2 PH	.177"	.138"	TCG	GJ1436DT**	128.00
14"	36T	3 1/8"	.177"	.138"	TCG	GJM1436T	128.00
16"	36T	2", 2 PH	.177"	.138"	TCG	GJ1636**	141.00
16"	50T	1"	.197"	.138"	TCG	GJ1650	185.00
18"	48T	2", 2 PH	.180"	.138"	TCG	GJ1848**	183.00

Notes

* Designed for Mereen-Johnson rip saws with 3 1/8" arbor and with one 1/4" keyway.
** Specially designed for cutting with Diehl saws, (2) 9/16" pin hole at 5" bolt circle.
*** For Raimann Rip Saw with 4 small 7 mm pins & 2 large 14mm pins, plus 2 keyways.
**** For super smooth rip cuts in thinner stock

Rip & Gang Saws - Alternating Top Bevel

These saws are designed to rip soft or hard woods where a strong grain pattern can cause the saw to drift and follow the grain. The ATB design helps maintain direction and provide a very clean and straight cut. 

All of these rip blades have a 20º hook angle and should be used for rip cuts only. They can be bored out to fit most gang rip saws. Email service@justsawblades.com for information on this service.

Diameter	Teeth	Bore and Pinhole	Kerf	Plate	Item #	Price
7 1/4"	24T	5/8"/KO	.110"	.079"	RS72524*	53.00
8"	24T	5/8"	.118"	.079"	RS824	55.00
8 1/2"	24T	5/8"	.118"	.087"	RS85024	58.00
10"	24T	5/8"	.126"	.087"	RS1024	54.00
10"	30T	5/8"	.134"	.094"	RS1030	65.00
12"	24T	1"	.134"	.094"	RS1224	61.00
12"	24T	70mm, 2 key	.134"	.094"	RS1224K**	63.00
12"	36T	1"	.126"	.087"	RS1236	77.00
12"	36T	1"	.134"	.094"	RS1236134	93.00

Notes

*  Has a knock-out bushing to adapt to a worm drive saw
** RS1224K- 70mm bores have two 20mm x 5mm keyways for SCM Rip Saws.